...
- Train 10 has special ICE-handling, so the ICE should always be assigned to this number, other Trains with this number stop for a while before parking.
- The home position of each train is hardcoded into the Controller
- The Controller tries to connect to a WebProvider on localhost:8089
- The Clear-Mode by the WebProvider overrides any destination in each tick and can currently not be disabled by the console
- The JSON kivis file is in the current execution folder: 'json_output.simin'
- The Controller uses ANSI-Escape sequences to color the output and overwrite recived contact messages.
- The entered characteres are most likely not all visible since there may be quite some output while typing, so these commands are typed blind in this case
...
+ | if present then there will be no startup hardware check which turns on the lamps and switches each point twice and cycles thrue signal colors with some delay |
|---|---|
fast_speed | pre-sets the global driving speed for the trains. Default: 70 |
slow_speed | pre-sets the global parking speed for the trains. Default: 59 |
trainX_pos | sets the position of the train X, caseinsensitive, prefixed with '-' for reversed on bidirectional tracks, valid only for segments (not for ex.: IC_JCT_0) examples: KH_ST_2, K2, 26, -KH_LN_3, IC_ST_3, I3, 10, OC_LN_4 |
| DEFAULT | fillst fills the remaining positions with the home Positons of each train |
Valid track identifyer identifier are the Track names (IC_ST_2, OC_LN_4), their numbers (9, 38) and for stations the short versions (I1, I2, I3, O1, O2, O3, K1, K2, K3, K4, K5).
If reverse is a possible information then a preceeding '-' signals this. All Track inputs should be case insensitive.
...
| <train_num> <target> | sets the target of a train |
|---|---|
| sc | schedule | print requested locks for each train |
| c | set destination of each train to their starting position |
| reset trains | set destinbation of each train to their home position (coded into the controller) |
| toggle bell | toggles the crossings-gate-bell On and Off |
| toggle lamp <range> | toggles selected lamps On and Off |
| enable lamp <range> | turns selected lamps On |
| disable lamp <range> | turns selected löamps Off |
| print tick | toggles the output of the current tick number each tick On and Off |
| r | toggles randommode |
| x | reconnects to the hardware |
| t | prints positions of each train |
| s | speeds | prints the speeds for each track |
| st | " " | (second option is only a space) toggles stop mode, which sets all hardware speeds to 0 |
| pt <point_num> | toggles a Point, only works when the point isn't locked |
| ts | prints the 4 speeds of each train (2nd and 4th number are the used slow and fast speeds) |
| setspeed [t<train_num>] <fast_speed> [slowspeed] | sets the global or train specific speeds |
| reach_t <track> | (DEBUG)sends a reached signal from this track |
| reach <train_num> | (DEBUG) sends a reached signal for given train |
| sim [s|e]<track> | (DEBUG) simulates the contacts on a track. s: only the first contact, e: only the second contact (no space after s or e) |
| dest | prints entered destination for each train |
| time | prints maximum and average time for different loop parts (stdin, input, tick, output), partition may not be fully accurate |
| trains | prints for each track the train ontop |
| move [on|off] | toggles or sets moveing mode, which sends some trains to two toggeling destinations, with some time waiting in a station |
| move_time <time> | sets waiting time in stations for moveing mode in ms (1000 = 1s) |
| clear | sets each destination to 0 (= IC_JCT_0 => Invalid, no Destination) |
| deb | currently has no effect, may be used for requested debug output |
| block <train_num> | toggles the 'dont_force_destination' input for the train. If enabled, this train would not start moveing to make space for another train |
| webprovider debug | toggles webprovider communication debug outputs |
| json output | toggles the creation of a '.simin' JSON file for kivis every 2s |
...